燃料变化对气体燃烧器燃烧性能影响的数值模拟研究

该文以John Zink公司一种瓦斯燃烧器为几何原型,对燃烧器和稳焰旋流器附近三维复杂形状未作任何简化,生成了包括燃烧器和炉膛的结构化网格,换用甲烷、乙烷、丙烷和丁烷四种不同的气体燃料,用标准的k-ε湍流模型、k-ε-g湍流扩散燃烧模型和蒙特卡洛辐射换热模型对燃烧器内的流动及燃烧状况进行了全尺寸数值模拟,预报了燃烧器内流场和温度场,考察燃料变化对炉内温度场的影响规律及燃气射流特性参数(Re·D1)对火焰长度的影响,对进一步优化设计燃烧器、提高加热炉热效率有很好的指导意义。     

单相多极开关磁阻发电机设计及性能仿真

分析中低速开关磁阻发电机运行及控制特点，提出一种基于准线性模型的设计方案和步骤，该方法克服了类比法的盲目性。编制了计算机设计仿真程序，给出了一台样机的设计结果和仿真曲线，结果表明方法合理，具备一定的精度，能满足工程设计的要求。     

平湖油气田储层及含油气预测

平湖油气田是东海第一个开发的复合型油气田 ,主要含油气层段为渐新统花港组油藏 (H2 -H8)和始新统平湖组气藏 (P1 -P1 1 ) ,首期开发区为F1、F2断块 ,二期开发区为B1、B2断块。在平湖油气田开发过程中 ,针对花港组油藏波阻抗与岩性相关性好 ,而平湖组中下部波阻抗与岩性相关性不好的这种地质和地球物理特点 ,应用国内外先进的技术和方法 ,尝试多种方法预测储层及含油气 ,取得了较好的预测成果。     

Chalcogenide Glasses Based on Germanium Disulfide for Second Harmonic Generation

High second‐order susceptibilities are created by thermal poling in bulk germanium disulfide based chalcogenide glasses. Experimental conditions of the poling treatment (temperature, voltage, time) were optimized for each glass composition. The second‐order nonlinear signals were recorded by using the Maker fringes experiment and a second‐order coefficient χ⁽²⁾ up to 8 pm V^–1 was measured in the Ge₂₅Sb₁₀S₆₅ glass. This value is obtained using a simulation based on accurate knowledge of the thickness of the nonlinear layer. Two mechanisms are proposed to explain the creation of a nonlinear layer under the anode: the formation and the migration of charged defects towards the anode may mainly occur in Ge₂₀Ga₅Sb₁₀S₆₅ and Ge₂₅Ga₅S₇₀ glasses, whereas the migration of Na⁺ ions towards the cathode may be responsible for the accumulation of negative charges under the anode in Ge₃₃S₆₇ and Ge₂₅Sb₁₀S₆₅ glasses. Different electronic conductivity behaviors seem to be at the origin of the phenomenon. In parallel, the potential effect of the poling treatment on the structural and electronic properties is studied using Raman spectroscopy and secondary ion mass spectroscopy measurements.     

Environment as a first class abstraction in multiagent systems

The current practice in multiagent systems typically associates the environment with resources that are external to agents and their communication infrastructure. Advanced uses of the environment include infrastructures for indirect coordination, such as digital pheromones, or support for governed interaction in electronic institutions. Yet, in general, the notion of environment is not well defined. Functionalities of the environment are often dealt with implicitly or in an ad hoc manner. This is not only poor engineering practice, it also hinders engineers to exploit the full potential of the environment in multiagent systems. In this paper, we put forward the environment as an explicit part of multiagent systems.We give a definition stating that the environment in a multiagent system is a first-class abstraction with dual roles: (1) the environment provides the surrounding conditions for agents to exist, which implies that the environment is an essential part of every multiagent system, and (2) the environment provides an exploitable design abstraction for building multiagent system applications. We discuss the responsibilities of such an environment in multiagent systems and we present a reference model for the environment that can serve as a basis for environment engineering. To illustrate the power of the environment as a design abstraction, we show how the environment is successfully exploited in a real world application. Considering the environment as a first-class abstraction in multiagent systems opens up new horizons for research and development in multiagent systems.     

机械过冷的制冷系统在汽车空调中的应用

由于很多汽车空调采用斜盘式压缩机，有利于采用机械过冷的制冷系统，来增加汽车空调的制冷量、提高制冷效率。本文的主要目的是通过对系统工质的流量分配、空调制冷量和性能系数(COP)与中间压力之间的变化关系的研究，来研究机械过冷在汽车空调中应用的可行性。     

An analytical model to determine the ultimate load on masonry arch bridges.

This paper proposes an analytical elasto–plastic model to describe the behavior of arches. The modeling is carried out using the equations of (i) horizontal equilibrium, (ii) vertical equilibrium and (iii) equilibrium of moments. The latter equations of equilibrium are ordinary differential equations which can easily be solved by adding boundary conditions, imposing restrictions on the horizontal and vertical movement and on the rotation in the abutments of the arch. For masonry arches, including material properties allowing the occurrence of cracks and the subsequent formation of hinges is required. The latter theory has been implemented in a computer program (Matlab), offering numerical simulations. The software was used to illustrate two case-studies, i.e., the assessment of an arch loaded with a vertical point load and one with a horizontal point load.     

Inspection and Process of Tension of Cables of General Rafael Urdaneta Bridge

In 1997 and 1999, inspection works were carried out in the 384 cable stays of the six central piers of General Rafael Urdaneta Bridge, located in Maracaibo, Venezuela. Inspection indicated the presence of water and significant settlings in the sockets of the cables and corrosion along each cable and socket. The tension of the cables was also measured, and differences of up to 30% in the tension of the cables of some of the 24 groups corresponding to the six central piers (four groups of 16 for each pier) were found. The results suggested the need to retension the cables. This paper shows the outcome of the inspection and indicates the procedure and results of the process of retension, finished in July 2000.     

Investigation of the Correlation between Texture and Microstructure on a Submicrometer Scale in the TEM

In recent years the investigation of local texture and microstructure by analysis of electron backscatter diffraction patterns (EBSP) in the SEM has become a very powerful and popular method. With the introduction of SEM with field emission guns (FEG) the spatial resolution of EBSP measurements could be enhanced from 500 nm with a tungsten emitter to better than 50 nm. This evolution of SEM techniques raises the question whether transmission electron microscopy (TEM) still has fields of application in texture research. The present article answers this question with a clear “yes” and presents three examples of investigations where TEM is indispensable. The three examples comprise the investigation of the correlation between dislocation structure and deformation texture, a study on nucleation mechanisms of recrystallization in highly deformed metals and the investigation of microtexture and microstructure in nanocrystalline materials. Together with the presentation of these cases some of the necessary measurement techniques are described briefly. It is shown that TEM has to be applied when highest spatial resolution of orientation determination and imaging and high accuracy of orientation determination are to be reached, when the three‐dimensional and quantitative characterization of lattice defects is required or when materials with a high density of lattice defects are to be investigated.